Tongue Controls for Genesis 3 Male Characters

This add-on enables you to easily control the tongue of your Genesis 3 Male characters.
It works with the Genesis 3 Male base character and all other Genesis 3 Male based characters, like Michael 7 etc. 

This product adds 14 custom dials to the character's parameters that enable you to easily adjust the tongue and tip and one to open the mouth:

- Open Mouth (this is just to be able to open the mouth quickly without opening another parameter group)
- Tongue Out
- Tongue Base Left / Right
- Tongue Base Twist
- Tongue Base Up / Down
- Tongue Floppy / Curly
- Tongue Curved L / R
- Tongue Thick / Thin
- Tongue Twist
- Tongue Wide / Narrow
- Tip Left / Right
- Tip Length
- Tip Twist
- Tip Up / Down


You can pose the tongue in almost countless different ways with this add on. Easily!
 
__________________________________________________________________
Requirements:

- DAZ Studio 4.8 or higher
- Genesis 3 Male Base Figure 

This product has been tested in DAZ Studio 4.8. 
Not tested in or recommended for Poser.

__________________________________________________________________
Installation:

Just extract the contents of this archive to your DAZ Studio library. 

__________________________________________________________________
Usage:

Select the whole character you want to use the add on with. Go to the PARAMETERS pane and select the property group named TONGUE CONTROLS. On the right side
you will see the different sliders. Usually you would start with opening the mouth. There is a slider for that too in the TONGUE CONTROLS group. 
Then you should use the 0 TONGUE OUT dial first to stick the tongue out as far as you like (within the limits). After that just use the desired dials to pose the tongue as you wish. The dials can be mixed but we suggest to dial slowly because depending how far you go and what you combine could result in odd poses. Depending on the tongue pose you might need to adjust the opening of the mouth or parting of the lips to avoid intersections of the tongue and lips. 
The TONGUE BASE UP/DOWN dial is also suitable to fine tune the tongue's position. 

All dials have set default limits. We suggest to leave the limits on for the most realistic results. You can get some unusual results by disabling the limits. For example, by disabling the 0 TONGUE OUT limits, you can make the tongue even longer if desired.
__________________________________________________________________

Creator: SF-DESIGN (SFD)
Contact: SITE MAIL
__________________________________________________________________

Copyright notice:

This product is copyrighted!
You may not resell this product or parts of it nor give it away for free. 
Redistribution is NOT permitted! You can use this product for your private and commercial work. 
Refer to the included "EndUserLicense" for further information. 

(c) 2015 by SF-DESIGN - all rights reserved.

__________________________________________________________________

Product Contents:

Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\baseud.dsf
Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\curlyfloppy.dsf
Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\mouthopen.dsf
Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\thickness.dsf
Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\tiplentgh.dsf
Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\tiplr.dsf
Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\tiptwist.dsf
Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\tipud.dsf
Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\tonguebasetwist.dsf
Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\tongueblr.dsf
Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\tonguelr.dsf
Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\Tongueout.dsf
Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\twist.dsf
Data\DAZ 3D\Genesis 3\Male\Morphs\SF-DESIGN\tpc\wider.dsf

Documentation\SFD Tongue Controls Genesis 3 Male ReadMe.txt